Top 10 Common Issues with Volvo 240 Models
Please keep in mind these issues arise due to the fact 240 Volvos as a whole, were built very robust and probably ended up being on the road longer than Volvo ever anticipated. It's one tough car! In general these are not “defects” or poor design, just stuff to be on the lookout for if you find yourself driving one of our favorite Volvos of all time.
Main Fuses
The main fuse box is located in the driver side kick panel and sufferes from a few design flaws. First, the fuse box is susceptible to corrosion from water that can enter the interior and drip directly onto the fuses.
Second, the small contact area of the European ceramic style fuses also leads to corrosion due to electrolosis. Prevent numerous problems associated with the fuse box, by pulling all fuses and cleaning them annually.
If you encounter a intermittent or no start issue on your Volvo 240, you can often get going again by simply spinning the fuses in their holders, which reestablishes electrical contact.
1975-93 30 Piece Fuse Kit for 240 & 260 - 105869
Heater Fan
The Volvo 240 is famous for it’s powerful heater, which according to urban legend can brown a slice of toast in about 30 seconds, however the heater blower motor is buried in the deepest confines of the dash. It’s like they built the Volvo around the heater motor! Fortunately the motors are of decent quality and if you’re lucky you’ll only have to replace it one time while you own the car. Replacing the motor can take 3-4 hours for an experienced mechanic and we’ve heard of reports of it taking all weekend from some beginner do-it yourselfers!
- 1975-93 Heater Blower Fan Motor - 101243
- 1975-93 Heater Blower Fan Motor - 124306
OD Relay, Wiring, Switch & Solenoid
Why in the world Volvo chose to use an electronic overdrive instead of a real 5 speed manual transmission is beyond us, but they did and we have all had to live with that decision. It proved to be a troublesome system over the years and here’s a few of the most common issues. Most common problem with the overdrive is due to the shift knob accidentally being pulled off of the shift lever (while trying to engage reverse), which results in the OD button wires being disconnected from the switch. Next is failure of the OD wires just below the shifter, where they simply fail from being flexed back and forth thousands of times. The switch in the gear shift knob can also go bad and don’t forget to check the wiring where it connects to the solenoid on the driver side of the transmission as the wires often get disconnected by accident. Last on the list are the solenoid and the overdrive themselves. The overdrive works off of hydraulic pressure and as they age, they begin to lose pressure and engagement will become unreliable. Often replacing the lightweight Type F auto trans fluid used in them with a 30-50 weight will provide a few more years of service.
- 1981-1984 Overdrive Relay - M46 240 - 102250
- 1982-1984 Overdrive Relay Automatic - 240 - 122073
- 1982-1984 Overdrive Relay Automatic - 240 -102365
- 1985-1993 Overdrive Relay Automatic - 240 - 104301
- 1985-1987 Overdrive Relay - 240 M46 - 112827
- 1985-1993 Overdrive Relay Automatic - 240 - 124254
Motor & Transmission Mounts
The Volvo 240 goes through engine and transmission mounts on a regular basis! To prevent serious damage you’ll need to inspect them annually. Be prepared to replace them every 2-3 years depending on how hard you drive the car. The reason for the unusually short lifespan of these parts is due to the safety related design. The mounts are designed to allow the engine to move back and under the car, keeping it out of the passenger compartment in the event of a serious head on collision.
- 1982-1993 Automatic Transmission Mount - 101238
- 1975-1993 Left Engine Mount - 240 - 120275
- 1975-1993 Right Engine Mount - 240 - 120276
- 1975-1993 Manual Transmission Mount - 101178
- 1975-1993 Right Engine Mount - 240 – 121310
- 1975-1993 Left Engine Mount - 240 - 121309
- 1975-1993 Right HD Engine Mount - 240 - 120274
- 1975-1993 Right Engine Mount - 240 - 124185
- 1976-1993 HD Manual Transmission Mount - 124425
- 1976-1993 HD Manual Transmission Mount - 101170
- 1987-1993 Transmission Mount 1985-1993 240 with 5 Speed M47 - 107090
Flame Trap System
Another Volvo oddity is the use of a flame trap system where every other car manufacturer in the world uses a PCV system incorporating a PCV valve. Volvo has had problems with this system since it was introduced in 1976. Volvo's still run into the same issues on their newer models. Possibly in theory Volvos system is better, but in reality it gets overlooked and inevitably becomes clogged up and causes oil leaks and idle problems.
- 1976-1980 Flame Trap Kit - 104325
- 1981-1987 Flame Trap Kit - NON Turbo - 114236
- 1988-1993 Flame Trap Kit - 114237
- 1988-1993 Flame Trap Kit - 104083
Worn Air Intake Hose & Air Box Thermostats
Volvo 240 models with Bosch LH electronic fuel injection have a large plastic accordion style intake hose that connects the air mass meter to the intake manifold. This hose rests on the inner fender, over time a hole will wear through where it touches.The problem is that you now have unfiltered and unmetered air entering the engine, which causes all sorts of erratic behavior. The car will be running lean and if you attempt to correct the mixture and get a decent idle unaware of the cause, you will introduce even more issues.Inspect the hose at every oil change and replace as necessary.
Also related to the intake system is the air box thermostat. This is a small valve located in the air box that routes hot air from the exhaust manifold to aid in cold start performance until the engine reaches normal operating temperature. It commonly fails in the open position allowing super heated air to be drawn into the engine, which reduces performance as well as dramatically shortening the life of the expensive air mass meter
- 1983-1993 Air Intake Hose - 240 Non Turbo - 124114
- 1983-1993 Air Intake Hose - 240 Non Turbo - 103212
Lumbar System & Seat Grid
The seats in the Volvo 240 are very comfortable when they are in good condition. Volvo 240 seats offer excellent adjustable lumbar back support. The lumbar system is very effective, but not the best design when it comes to longevity. These lumbar support systems commonly fail between 50-100,000 miles. The bottom seat cushion support grid is also a weak spot, causing drivers to struggle when trying to see over the steering wheel when it fails. This part was discontinued by Volvo a few years ago and we will be introducing an improved version this fall.
- 1975-1993 Seat Grid - 114760
- 1975-1993 Seat Grid Spring - Long - 114676
- 1975-1993 Seat Grid Spring - Short - 114678
Watertight Fuse Holder
For owners of 1982-89 non-turbo Volvo 240 series, Volvos with LH fuel injection. Here’s a chance to put an end to intermittent electrical problems with our watertight fuse holder system. With the Bosch® LH fuel injection system, current is supplied from the battery to an exposed blade style fuse. This addresses the problem. The fuse is located about a foot behind the battery on the driver’s side inner fender. Over time, corrosion of the fuse holder causes problems with the electrical system, including starting difficulties and intermittent stalling of the engine. Visual clues of corrosion in your Volvo 240 are discolored connections and a deformed or melted plastic fuse holder. Our waterproof replacement will put an end to this problem by concealing the fuse and terminals from water and corrosive gases. Also included are connectors and heat-shrink tubing to prevent the splice from corroding and a new 25-amp fuse. Don’t be fooled by similar looking systems. We tested several, and this is the only one we found to be water-tight.
- 1982-1989 Watertight Fuse Holder - 102452
Fuel Injection Relay 1978-1985 240 Models
The main fuel pump relay can be troublesome causing intermittent stalls and hard starting. The most common failure is overheating of the main 12V power connection to the point that the solder joint fails. This is usually caused by a failed pre pump in the gas tank, which in turn causes the main fuel pump to be overworked and draw excessive amperage that overheats the circuit.You can confirm this failure by popping the cover off the relay and inspecting the solder joints on the circuit board.
- 1978-1985 Fuel Pump Relay 240 with K-Jetronic - 102240
- 1978-1985 Fuel Pump Relay 240 with K-Jetronic - 113773
- 1982-1984 Fuel Pump Relay 240 Non-Turbo with LH-Jetronic - 108663
- 1985-1993 Fuel Pump Relay - 104561
- 1985-1993 Fuel Pump Relay - 113772
Fuel System Pre Pump 1978-1993 240 Models
The pre pump is a low-pressure, high-volume pump that sits inside the gas tank and supplies fuel to the main high pressure pump under the car. When it fails, symptoms include poor idle quality, hesitation when accelerating, reduced fuel economy, loud humming noises emanating from the main pump and accelerated wear of the main pump. Faulty pre pumps can also lead to hi amperage loading of the fuel pump electrical circuit resulting in blown fuses and or failed relays as mentioned above.
- 1975-1983 In Tank Fuel Pump - 101204
- 1982-1993 Main Fuel Pump - 100281
- 1984-1993 In Tank Fuel Pre-Pump - 101250
Other Common Issues
Heater core & heater control valves leaking into the interior
Worn out ignition switch resulting in the loss of some major electrical circuits
Failed wiring insulation on the main engine wiring harness 1982-1985